DS92LV010A

www.ti.com

SNLS007E –MAY 1998–REVISED APRIL 2013

DS92LV010A Bus LVDS 3.3/5.0V Single Transceiver

Check for Samples: DS92LV010A

FEATURES

DESCRIPTION

The DS92LV010A is one in a series of transceivers

• Bus LVDS Signaling (BLVDS)

designed specifically for the high speed, low power

• Designed for Double Termination Applications

proprietary bus backplane interfaces. The device

• Balanced Output Impedance

operates from a single 3.3V or 5.0V power supply

and includes one differential line driver and one

• Lite Bus Loading 5pF Typical

receiver. To minimize bus loading the driver outputs

• Glitch Free Power Up/Down (Driver Disabled)

and receiver inputs are internally connected. The

• 3.3V or 5.0V Operation

logic interface provides maximum flexibility as 4

separate lines are provided (DIN, DE, RE, and

• ±1V Common Mode Range

ROUT). The device also features flow through which

• ±100mV Receiver Sensitivity

allows easy PCB routing for short stubs between the

• High Signaling Rate Capability (Above 100

bus pins and the connector. The driver has 10 mA

Mbps)

drive capability, allowing it to drive heavily loaded

backplanes, with impedance as low as 27 Ohms.

• Low Power CMOS Design

• Product Offered in 8 Lead SOIC Package

The driver translates between TTL levels (single-

ended) to Low Voltage Differential Signaling levels.

• Industrial Temperature Range Operation

This allows for high speed operation, while

consuming minimal power with reduced EMI. In

addition the differential signaling provides common

mode noise rejection of ±1V.

The receiver threshold is ±100mV over a ±1V

common mode range and translates the low voltage

differential levels to standard (CMOS/TTL) levels.

CONNECTION DIAGRAM

Figure 1. SOIC Package

See Package Number D0008A

BLOCK DIAGRAM

Figure 2.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

DS92LV010A

SNLS007E –MAY 1998–REVISED APRIL 2013

www.ti.com

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

ABSOLUTE MAXIMUM RATINGS

(1)(2)(3)

Supply Voltage (V

) 6.0V

Enable Input Voltage (DE, RE) −0.3V to (V

+ 0.3V)

Driver Input Voltage (DIN) −0.3V to (V

+ 0.3V)

Receiver Output Voltage (R

OUT

) −0.3V to (V

+ 0.3V)

Bus Pin Voltage (DO/RI±) −0.3V to + 3.9V

Driver Short Circuit Current Continuous

ESD (HBM 1.5 kΩ, 100 pF) >2.0 kV

Maximum Package Power Dissipation at 25°C SOIC 1025 mW

Derate SOIC Package 8.2 mW/°C

Junction Temperature +150°C

Storage Temperature Range −65°C to +150°C

Lead Temperature (Soldering, 4 sec.) 260°C

(1) All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground except

, V

and V

unless otherwise specified.

(2) Absolute Maximum Ratings are these beyond which the safety of the device cannot be ensured. They are not meant to imply that the

device should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.

(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and

specifications.

RECOMMENDED OPERATING CONDITIONS

Min Max Units

Supply Voltage (V

), or 3.0 3.6 V

Supply Voltage (V

) 4.5 5.5 V

Receiver Input Voltage 0.0 2.9 V

Operating Free Air Temperature −40 +85 °C

Product Folder Links: DS92LV010A

DS92LV010A

www.ti.com

SNLS007E –MAY 1998–REVISED APRIL 2013

3.3V DC ELECTRICAL CHARACTERISTICS

(1)(2)

= −40°C to +85°C unless otherwise noted, V

= 3.3V ± 0.3V

Parameter Test Conditions Pin Min Typ Max Units

Output Differential Voltage R

= 27Ω, See Figure 3 DO+/RI+, 140 250 360 mV

DO−/RI−

ΔV

Magnitude Change 3 30 mV

Offset Voltage 1 1.25 1.65 V

ΔV

Offset Magnitude Change 5 50 mV

OSD

Output Short Circuit Current V

= 0V, DE = V

−12 −20 mA

Voltage Output High V

= +100 mV I

= −400 µA R

OUT

2.8 3 V

Inputs Open 2.8 3 V

Inputs Shorted 2.8 3 V

Inputs Terminated, R

= 27Ω 2.8 3 V

Voltage Output Low I

= 2.0 mA, V

= −100 mV 0.1 0.4 V

Output Short Circuit Current V

OUT

= 0V, V

= +100 mV −5 −35 −85 mA

Input Threshold High DE = 0V DO+/RI+, +100 mV

DO−/RI−

Input Threshold Low −100 mV

Input Current DE = 0V, V

= +2.4V, or 0V −20 ±1 +20 µA

= 0V, V

= +2.4V, or 0V −20 ±1 +20 µA

Minimum Input High Voltage DIN, 2.0 V

DE,RE

Maximum Input Low Voltage GND 0.8 V

Input High Current V

= V

or 2.4V ±1 ±10 µA

Input Low Current V

= GND or 0.4V ±1 ±10 µA

Input Diode Clamp Voltage I

CLAMP

= −18 mA −1.5 −0.8 V

CCD

Power Supply Current DE = RE = V

, R

= 27Ω V

13 20 mA

CCR

DE = RE = 0V 5 8 mA

CCZ

DE = 0V, RE = V

3 7.5 mA

DE = V

, RE = 0V, R

= 27Ω 16 22 mA

output

Capacitance @ BUS Pins DO+/RI+, 5 pF

DO−/RI−

(1) All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground except

, V

and V

unless otherwise specified.

(2) All typicals are given for V

= +3.3V or 5.0 V and T

= +25°C, unless otherwise stated.

Product Folder Links: DS92LV010A

Part #	DS92LV010ATMX
Description	BUS LVDS 3.3/5.0V SINGLE TRANSCEIVER - Tape and Reel
Category	IC
Availability	Out of Stock
Qty	0

DS92LV010ATMX

Related Items

Technical Document