3
PS8822B 04/03/06
PI6C10804
1.8V/2.5V, 250MHz, 1:4 Networking Clock Buffer
1.8V AC Characteristics (Over Operating Range: V
DD
= 1.8V ± 0.15V, T
A
= -40° to 85°C)
Parameters Description
Test Conditions
(1)
Min. Typ Max. Units
F
IN
Input Frequency 0 180 MHz
t
R
/t
F
CLKn Rise/Fall Time 20% to 80% 1.0 ns
t
PLH,
t
PHL
(2)
Propagation Delay BUF_IN to CLKn
C
L
= 5pF, 125 MHz
Outputs are measured
@ Vdd/2
1.0 2.0 3.0 ns
t
SK(O)
(3)
Output to Output Skew between any two
outputs of the same device @ same transition
100 150
pst
SK(P)
(3)
Pulse Skew between opposite transitions
(t
PHL
-t
PLH
) of the same output
200 275
t
SK(T)
(3)
Part to Part Skew between two identical out-
puts of different parts on the same board
(4)
300
t
dc_in
Duty Cycle In @ 1ns edge rate 40 60
%
t
dc_out
Duty Cycle Out 40 60
Notes:
1. See test circuit and waveforms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. Skew measured at worse cast temperature (max. temp).
4. Identical conditions: loading, transitions, supply voltage, temperature, package type and speed grade.
Storage Temperature...........................................................–65°C to +150°C
V
DD
Voltage ..........................................................................–0.5V to +2.5V
Output Voltage (max 2.5V) .......................................... –0.5V to V
DD
+0.5V
Input Voltage (max 2.5V) ............................................. –0.5V to V
DD
+0.5V
1.8V Absolute Maximum Ratings (Above which the useful life may be impaired. For user guidelines only, not tested.)
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional operation
of the device at these or any other conditions above those
indicated in the operational sections of this specication is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect reliability.
1.8V DC Characteristics (Over Operating Range: V
DD
= 1.8V ± 0.15V, T
A
= -40° to 85°C)
Param-
eters
Description
Test Conditions
(1)
Min.
Typ.
(2)
Max. Units
V
DD
Supply Voltage 1.65 1.8 1.95 V
V
IH
Input HIGH Voltage Logic HIGH level 0.65*Vdd 2.7
V
V
IL
Input LOW Voltage Logic LOW level -0.3 0.35*Vdd
I
I
Input Current
(3)
V
DD
= Max,
Vin = V
DD
or GND
I/O pins 15
µA
non I/O pins 5
V
OH
Output High Voltage V
DD
= Min., V
IN
= V
IH
or V
IL
I
OH
= -2mA 1.3
V
I
OH
= -8mA 1.2
V
OL
Output LOW Voltage V
DD
= Min., V
IN
- V
IH
or V
IL
I
OL
= 2mA 0.45
I
OL
= -8mA 0.45
Notes:
1. For Max. or Min. conditions, use appropriate operating Vdd and Ta values.
2. Typical values are at V
CC
= 1.8V, +25°C ambient and maximum loading.
3. This parameter is determined by device characterization but is not production tested.