184

2545M–AVR–09/07

ATmega48/88/168

Note: 1. See ”About Code Examples” on page 9.

The receive function example reads all the I/O Registers into the Register File before any com-

putation is done. This gives an optimal receive buffer utilization since the buffer location read

will be free to accept new data as early as possible.

19.7.3 Receive Compete Flag and Interrupt

The USART Receiver has one flag that indicates the Receiver state.

Assembly Code Example

(1)

USART_Receive:

; Wait for data to be received

sbis UCSRnA, RXCn

rjmp USART_Receive

; Get status and 9th bit, then data from buffer

in r18, UCSRnA

in r17, UCSRnB

in r16, UDRn

; If error, return -1

andi r18,(1<<FEn)|(1<<DORn)|(1<<UPEn)

breq USART_ReceiveNoError

ldi r17, HIGH(-1)

ldi r16, LOW(-1)

USART_ReceiveNoError:

; Filter the 9th bit, then return

lsr r17

andi r17, 0x01

ret

C Code Example

(1)

unsigned int USART_Receive( void )

{

unsigned char status, resh, resl;

/* Wait for data to be received */

while ( !(UCSRnA & (1<<RXCn)) )

;

/* Get status and 9th bit, then data */

/* from buffer */

status = UCSRnA;

resh = UCSRnB;

resl = UDRn;

/* If error, return -1 */

if ( status & (1<<FEn)|(1<<DORn)|(1<<UPEn) )

return -1;

/* Filter the 9th bit, then return */

resh = (resh >> 1) & 0x01;

return ((resh << 8) | resl);

}

185

2545M–AVR–09/07

ATmega48/88/168

The Receive Complete (RXCn) Flag indicates if there are unread data present in the receive

buffer. This flag is one when unread data exist in the receive buffer, and zero when the receive

buffer is empty (i.e., does not contain any unread data). If the Receiver is disabled (RXENn = 0),

the receive buffer will be flushed and consequently the RXCn bit will become zero.

When the Receive Complete Interrupt Enable (RXCIEn) in UCSRnB is set, the USART Receive

Complete interrupt will be executed as long as the RXCn Flag is set (provided that global inter-

rupts are enabled). When interrupt-driven data reception is used, the receive complete routine

must read the received data from UDRn in order to clear the RXCn Flag, otherwise a new inter-

rupt will occur once the interrupt routine terminates.

19.7.4 Receiver Error Flags

The USART Receiver has three Error Flags: Frame Error (FEn), Data OverRun (DORn) and

Parity Error (UPEn). All can be accessed by reading UCSRnA. Common for the Error Flags is

that they are located in the receive buffer together with the frame for which they indicate the

error status. Due to the buffering of the Error Flags, the UCSRnA must be read before the

receive buffer (UDRn), since reading the UDRn I/O location changes the buffer read location.

Another equality for the Error Flags is that they can not be altered by software doing a write to

the flag location. However, all flags must be set to zero when the UCSRnA is written for upward

compatibility of future USART implementations. None of the Error Flags can generate interrupts.

The Frame Error (FEn) Flag indicates the state of the first stop bit of the next readable frame

stored in the receive buffer. The FEn Flag is zero when the stop bit was correctly read (as one),

and the FEn Flag will be one when the stop bit was incorrect (zero). This flag can be used for

detecting out-of-sync conditions, detecting break conditions and protocol handling. The FEn

Flag is not affected by the setting of the USBSn bit in UCSRnC since the Receiver ignores all,

except for the first, stop bits. For compatibility with future devices, always set this bit to zero

when writing to UCSRnA.

The Data OverRun (DORn) Flag indicates data loss due to a receiver buffer full condition. A

Data OverRun occurs when the receive buffer is full (two characters), it is a new character wait-

ing in the Receive Shift Register, and a new start bit is detected. If the DORn Flag is set there

was one or more serial frame lost between the frame last read from UDRn, and the next frame

read from UDRn. For compatibility with future devices, always write this bit to zero when writing

to UCSRnA. The DORn Flag is cleared when the frame received was successfully moved from

the Shift Register to the receive buffer.

The Parity Error (UPEn) Flag indicates that the next frame in the receive buffer had a Parity

Error when received. If Parity Check is not enabled the UPEn bit will always be read zero. For

compatibility with future devices, always set this bit to zero when writing to UCSRnA. For more

details see “Parity Bit Calculation” on page 177 and “Parity Checker” on page 185.

19.7.5 Parity Checker

The Parity Checker is active when the high USART Parity mode (UPMn1) bit is set. Type of Par-

ity Check to be performed (odd or even) is selected by the UPMn0 bit. When enabled, the Parity

Checker calculates the parity of the data bits in incoming frames and compares the result with

the parity bit from the serial frame. The result of the check is stored in the receive buffer together

with the received data and stop bits. The Parity Error (UPEn) Flag can then be read by software

to check if the frame had a Parity Error.

186

2545M–AVR–09/07

ATmega48/88/168

The UPEn bit is set if the next character that can be read from the receive buffer had a Parity

Error when received and the Parity Checking was enabled at that point (UPMn1 = 1). This bit is

valid until the receive buffer (UDRn) is read.

19.7.6 Disabling the Receiver

In contrast to the Transmitter, disabling of the Receiver will be immediate. Data from ongoing

receptions will therefore be lost. When disabled (i.e., the RXENn is set to zero) the Receiver will

no longer override the normal function of the RxDn port pin. The Receiver buffer FIFO will be

flushed when the Receiver is disabled. Remaining data in the buffer will be lost

19.7.7 Flushing the Receive Buffer

The receiver buffer FIFO will be flushed when the Receiver is disabled, i.e., the buffer will be

emptied of its contents. Unread data will be lost. If the buffer has to be flushed during normal

operation, due to for instance an error condition, read the UDRn I/O location until the RXCn Flag

is cleared. The following code example shows how to flush the receive buffer.

Note: 1. See ”About Code Examples” on page 9.

19.8 Asynchronous Data Reception

The USART includes a clock recovery and a data recovery unit for handling asynchronous data

reception. The clock recovery logic is used for synchronizing the internally generated baud rate

clock to the incoming asynchronous serial frames at the RxDn pin. The data recovery logic sam-

ples and low pass filters each incoming bit, thereby improving the noise immunity of the

Receiver. The asynchronous reception operational range depends on the accuracy of the inter-

nal baud rate clock, the rate of the incoming frames, and the frame size in number of bits.

19.8.1 Asynchronous Clock Recovery

The clock recovery logic synchronizes internal clock to the incoming serial frames. Figure 19-5

illustrates the sampling process of the start bit of an incoming frame. The sample rate is 16 times

the baud rate for Normal mode, and eight times the baud rate for Double Speed mode. The hor-

izontal arrows illustrate the synchronization variation due to the sampling process. Note the

larger time variation when using the Double Speed mode (U2Xn = 1) of operation. Samples

denoted zero are samples done when the RxDn line is idle (i.e., no communication activity).

Assembly Code Example

(1)

USART_Flush:

sbis UCSRnA, RXCn

ret

in r16, UDRn

rjmp USART_Flush

C Code Example

(1)

void USART_Flush( void )

{

unsigned char dummy;

while ( UCSRnA & (1<<RXCn) ) dummy = UDRn;

}

Part #	ATMEGA48-20AU
Description	MCU 8BIT ATMEGA RISC 4KB FLASH 3.3V/5V 32TQFP - Trays
Category	IC
Availability	Out of Stock
Qty	0

ATMEGA48-20AU

Related Items

Technical Document