Harris Corporation AC161

Cross Number:

Item Description:







Technical Document


DISCLAIMER: The information provided herein is solely for informational purposes. Customers must be aware of the suitability of this product for their application, and consider that variable factors such as Manufacturer, Product Category, Date Codes, Pictures and Descriptions may differ from available inventory.

CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper I.C. Handling Procedures.
Copyright
© Harris Corporation 1994
1
SEMICONDUCTOR
CD54AC161/3A
CD54ACT161/3A
Synchronous Presettable Binary Counters
Functional Diagram
ACT INPUT LOAD TABLE
INPUT UNIT LOAD (NOTE 1)
Pn 0.13
CP 1
MR, TE 0.83
SPE 0.67
PE 0.5
NOTE:
1. Unit load is I
CC
limit specified in DC Electrical Specifications
Table, e.g., 2.4mA Max at +25
o
C.
SPE
CP
MR
PE
TE
9
2
1
7
10
GND = 8
V
CC
= 16
3456
14
13
12
11
15
Q0
Q1
Q2
Q3
TC
P0 P1 P2 P3
June 1997
File Number
3892
Description
The CD54AC161/3A and CD54ACT161/3A are synchronous
presettable binary counters that utilize the Harris Advanced
CMOS Logic technology. The CD54AC161/3A and
CD54ACT161/3A are asynchronously reset. Counting and
parallel presetting are both accomplished synchronously
with the negative-to-positive transition of the clock.
A LOW level on the Synchronous Parallel Enable input,
SPE,
disables the counting operation and allows data at the P0 to
P3 inputs to be loaded into the counter (provided that the
setup and hold requirements for
SPE are met).
The counters are reset with a LOW level on the Master
Reset input,
MR.
Two count enables, PE and TE, in each counter are provided
for n-bit cascading. Reset action occurs regardless of the
level of the
SPE, PE, TE and CP inputs.
The look-ahead carry feature simplifies serial cascading of
the counters. Both count enable inputs (PE and TE) must be
HIGH to count. The TE input is gated with the Q outputs of
all four stages so that at the maximum count, the terminal
count (TC) output goes HIGH for one clock period. This TC
pulse is used to enable the next cascaded stage.
The CD54AC161/3A and CD54ACT161/3A are supplied in
16 lead dual-in-line ceramic packages (F suffix).
Absolute Maximum Ratings
DC Supply Voltage, V
CC
. . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +6V
DC Input Diode Current, I
IK
For V
I
< -0.5V or V
I
> V
CC
+ 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA
DC Output Diode Current, I
OK
For V
O
< -0.5V or V
O
> V
CC
+ 0.5V. . . . . . . . . . . . . . . . . . . . .±50mA
DC Output Source or Sink Current, Per Output Pin, I
O
For V
O
> -0.5V or V
O
< V
CC
+ 0.5V. . . . . . . . . . . . . . . . . . . . .±50mA
DC V
CC
or GND Current, I
CC
or I
GND
For Up to 4 Outputs Per Device, Add ±25mA For Each
Additional Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±100mA
Power Dissipation Per Package, P
D
T
A
= -55
o
C to +100
o
C (Package F) . . . . . . . . . . . . . . . . . . 500mW
T
A
= +100
o
C to +125
o
C (Package F) . . . . . . . . Derate Linearly at
8mW/
o
C to 300mW
Operating Temperature Range, T
A
Package Type F . . . . . . . . . . . . . . . . . . . . . . . . . .-55
o
C to +125
o
C
Storage Temperature, T
STG
. . . . . . . . . . . . . . . . . .-65
o
C to +150
o
C
Lead Temperature (During Soldering)
At Distance 1/16in. ± 1/32in. (1.59mm ± 0.79mm)
From Case For 10s Max . . . . . . . . . . . . . . . . . . . . . . . . . . +265
o
C
Unit Inserted Into a PC Board (Min Thickness 1/16in., 1.59mm)
With Solder Contacting Lead Tips Only. . . . . . . . . . . . . . . +300
o
C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Recommended Operating Conditions
Supply Voltage Range, V
CC
Unless Otherwise Specified, All Voltages Referenced to GND
T
A
= Full Package Temperature Range
CD54AC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5V to 5.5V
CD54ACT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V
DC Input or Output Voltage, V
I
, V
O
. . . . . . . . . . . . . . . . . . 0V to V
CC
Operating Temperature, T
A
. . . . . . . . . . . . . . . . . . .-55
o
C to +125
o
C
Input Rise and Fall Slew Rate, dt/dv
at 1.5V to 3V (AC Types) . . . . . . . . . . . . . . . . . . . 0ns/V to 50ns/V
at 3.6V to 5.5V (AC Types) . . . . . . . . . . . . . . . . . 0ns/V to 20ns/V
at 4.5V to 5.5V (AC Types) . . . . . . . . . . . . . . . . . 0ns/V to 10ns/V
COMING SOON!
COMPLETE DATA SHEET

Freelance Electronics
13197 Sandoval Street
Santa Fe Springs, CA 90670

Hours of Operation
Monday-Friday 7:30am-4:30pm PST
(Deadline for next day shipment 2:00pm PST)

Trustworthy Standards Serving the Electronic Components
Industry since 1986

Government Cage code#-1V4R6
Duns Number# 788130532
Certified Small Disadvantaged Business