Aluminum Electrolytic Capacitor/TG
Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.
Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.
EE74
TG
V
Series:
Type :
-40 to +125°C
10 to 100 V .DC
10 to 4700 µ F
±20 % (120Hz/+20°C)
I 0.01 CV or 3(µ A) after 2 minutes (whichever, greater)
W.V. (V) 10 16 25 35 50 63 80 100
-25 / +20 °C 3 2 2 2 2 2 2 2
-40 / +20 °C 6 4 4 3 3 3 3 3
(µF)
TG
Surface Mount Type
■ Features
Endurance:125°C 1000 to 2000 h
Miniaturization(40% less than TA Series)
Low ESR(Low temp)
Vibration-proof product is available upon request.(φ8 )
■ Specifications
Category temp. range
Rated W.V. Range
Nominal Cap. Range
Capacitance Tolerance
DC Leakage Current
tan δ
Characteristics
at Low Temperature
Endurance
Shelf Life
Resistance to
Soldering Heat
■ Marking
W.V. code
Negative polarity
marking
Series
identification
Capacitance
Lot number
W.V. code
( ) reference size
■ Dimensions in mm (not to scale)
After applying rated working voltage for 1000 hours(φ8x6.2), 2000 hours(8x10.2
<
) at +125
±2°C and then being stabilized at +20°C, capacitors shall meet the following limits.
After storage for 1000 hours at +125±2°C with no voltage applied and then being stabilized
at +20°C, capacitors shall meet the limits specified in Endurance.(With voltage treatment)
Capacitance change
tan δ
DC leakage current
Capacitance change
tan δ
DC leakage current
After reflow soldering ( Refer to page 20 for recommendable temperature profile.) and then
being stabilized at +20°C, capacitor shall meet the following limits.
±10 % of initial measured value
initial specified value
initial specified value
±30 % of initial measured value
(code U:±35%)
300 % of initial specified value (code U:350%)
initial specified value
Please see the attached standard products list
(Inpedance ratio at 120Hz)
K
0.3 max
φD±0.5
w
(I)
(P)
(I)
H
E~G=L±0.3
H~K=L±0.5
A±0.2
Japan
<
=
<
=
<
=
<
=
<
=
Corresponds to use in the car engine room.
The best for an electronically controlled
unit (ECU, ABS etc).
■ Application
=
TG
(
>
φ12.5)
=
W.V. code
(µF)
Capacitance
Lot number
Series
identification
Negative polarity
marking
(
<
φ10)
=
V 10 16 25 35
Code A C E V
V 50 63 80 100
Code H J K 2A
D L A,B H max. I W P K
Size
code
8.0 6.2 8.3 9.5
3.4 0.65 ±0.1 2.2 0.35
8.0 10.2 8.3 10.0
3.4 0.90 ±0.2 3.1 0.70
10.0 10.2 10.3 12.0
3.5 0.90 ±0.2 4.6 0.70
12.5 13.5 13.5 15.0 4.7 0.90 ±0.3 4.4 0.70
16.0 16.5 17.0 19.0 5.5 1.20±0.3 6.7 0.70
18.0 16.5 19.0 21.0 6.7 1.20 ±0.3 6.7 0.70
±0.20
E
F
G
H13
J16
K16
-0.20 to +0.15
±0.20
±0.30
±0.30
±0.30
B±0.2
<
=
