Technical data

Operating temperature range Max. operating temperature T

op,max

+125 °C

Upper category temperature T

max

+125 °C

Lower category temperature T

min

55 °C

Rated temperature T

+85 °C

Dissipation factor tan δ (in 10

-3

) at C

≤ 0.1 µF 0.1 µF < C

≤ 1 µF C

> 1 µF

at 20 °C

1 kHz 8 8 10

(upper limit values) 10 kHz 15 15 

100 kHz 30  

Insulation resistance R

ins

≤ 0.33 µF C

> 0.33 µF

or time constant τ = C

 R

ins

≤ 100 V DC 3750 MΩ 1250 s

at 20 °C, rel. humidity ≤ 65% ≥ 250 V DC 7500 MΩ 2500 s

(minimum as-delivered values)

DC test voltage 1.4  V

, 2 s

Category voltage V

(°C) DC voltage derating AC voltage derating

(continuous operation with V

≤ 85 V

= V

C,RMS

= V

RMS

or V

at f ≤ 60 Hz) 85<T

≤125 V

= V

 (165T

)/80 V

C,RMS

RMS

 (165T

)/80

Operating voltage V

for

(°C) DC voltage (max. hours) AC voltage (max. hours)

short operating periods T

≤ 100 V

= 1.25  V

(2000 h) V

= 1.0  V

C,RMS

(2000 h)

or V

at f ≤ 60 Hz) 100<T

≤125 V

= 1.25  V

(1000 h) V

= 1.0  V

C,RMS

(1000 h)

Damp heat test 56 days/40 °C/93% relative humidity

Limit values after damp Capacitance change ∆C/C ≤ 5%

heat test Dissipation factor change ∆ tan δ ≤ 5  10

-3

(at 1 kHz)

Insulation resistance R

ins

≥ 50% of minimum

or time constant τ = C

 R

ins

as-delivered values

Reliability:

Failure rate λ 1 fit (≤ 1  10

-9

/h) at 0.5  V

, 40 °C

Service life t

200 000 h at 1.0  V

, 85 °C

For conversion to other operating conditions and temperatures,

refer to chapter "Quality, 2 Reliability".

Failure criteria:

Total failure Short circuit or open circuit

Failure due to variation Capacitance change ∆C/C > 10%

of parameters Dissipation factor tan δ > 2  upper limit value

Insulation resistance R

ins

< 150 MΩ (C

≤ 0.33 µF)

or time constant τ = C

 R

ins

< 50 s (C

> 0.33 µF)

B32520 ... B32529

General purpose (stacked/wound)

Page 22 of 45Please read Important notes

at the end of this document.

Pulse handling capability

"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal

voltages, expressed in V/µs.

" represents the maximum permissible pulse characteristic of the waveform applied to the

capacitor, expressed in V

/µs.

Note:

The values of dV/dt and k

provided below must not be exceeded in order to avoid damaging the

capacitor.

dV/dt values

S = Stacked, W = Wound

Lead spacing 5 mm 7.5 mm 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm

Technology S S S W S W W W W

RMS

V DC V AC dV/dt in V/µs

63 40 250 120 50  30  3 1 0.8

100 63 300 150 75  50 5 4 3 1

250 160 400 200 150  100 10 8 5 4

400 200 600 275 175  125  10 8.5 6

450 200      20   

630 400 800  320  150  15 12 

values

S = Stacked, W = Wound

Lead spacing 5 mm 7.5 mm 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm

Technology S S S W S W W W W

RMS

V DC V AC k

in V

/µs

63 40 30000 15000 6300  3800  375 130 100

100 63 60000 30000 15000  10000 850 800 600 200

250 160 200000 100000 75000  50000 5000 4000 2500 2000

400 200 500000 220000 140000  100000  10000 8500 6000

450 200      15000   

630 400 1000000  400000  190000  18000 15000 

B32520 ... B32529

General purpose (stacked/wound)

Page 23 of 45Please read Important notes

at the end of this document.

Impedance Z versus frequency f

(typical values)

B32520 ... B32529

General purpose (stacked/wound)

Page 24 of 45Please read Important notes

at the end of this document.

Part #	B32520C1104J189
Description	CAP FILM 0.1UF 5% 100VDC RADIAL Additional Information:
Category	CAPACITOR
Availability	Out of Stock
Qty	0

B32520C1104J189

Related Items

Technical Document